The differences between Layer 2 VPN and Layer 3 VPN are as follows -

A layer 2 switch can assign VLANs to specific switch ports, which in turn are in different layer 3 subnets, and therefore in different broadcast domains. VLANs allow for greater flexibility by allowing different layer 3 networks to be sharing the same layer 2 infrastructure. Layer 3 VPN is less transparent compared to Layer 2 VPN and can meddle with applications. Customers make connectivity of remote customer sites with the Layer 3 (IP) connectivity and not the service provider. Layer 3 (IP) connectivity of the customer is made with the edge devices of the provider sites. Mar 16, 2012 · Layer 2 point-to-point Layer 3 IP VPN Layer 2 VPLS; MPLS Layer 2 Point to Point. Layer 2 point-to-point is a cost-effective way and a flexible alternative to high bandwidth leased lines. Many wholesale network operators have based their core network infrastructure on ethernet and use Layer 2. Oct 09, 2019 · Layer 2 has two options and Layer 3 has one. Layer 2 Businesses often use a VPN simply to secure their internet usage within an office, but having a Layer 2 VPLS is a step up. Internet providers who have an existing Layer 2 network (such as ATM or Frame Relay) may choose to use these VPNs instead of the other common MPLS VPN, Layer 3. There is no one IETF standard for Layer 2 MPLS VPNs. Instead, two methodologies may be used. Both methods use a standard MPLS header to encapsulate data.

Once a given packet is labeled the intervening devices simply forward it based on whatever LSP has been signaled. In the case of an L3VPN, the packet is a fully formed IP packet. In the case of an L2VPN a frame from a particular interface has a label added and is forwarded.

Layer two VPN Making use of Enhanced 802.1Q Tunneling. 802.1Q tunneling allows support organizations to supply a Layer two VPN service, often referred to as Layer 2 transparent LAN products and services (TLS) or Ethernet LAN products and services, using a VLAN-in-VLAN hierarchy and marking the labeled packets. The VPN connection is provided under three service. These services are VPWS (Virtual Private Wire Service), VPLS (Virtual Private LAN Service) and VPRN (Virtual Private Routed Network). VPWS and VPLS are L2 VPN service. VPRN is Layer 3 VPN service. To sum up the services given under Alcatle-Lucent service routers, let’s check these services Layer 3 VPN (L3VPN) is a type of VPN mode that is built and delivered on OSI layer 3 networking technologies. The entire communication from the core VPN infrastructure is forwarded using layer 3 virtual routing and forwarding techniques. Layer 3 VPN is also known as virtual private routed network (VPRN). The main functionality of layer3 switch is to connect various devices simultaneously. 2. It supports MPLS and VPN services. It does not support MPLS and VPN services. 3. It’s throughput is lower than layer-3 switch. While it provides high throughput. 4. In this, switching capacity is lower than layer-3 switch. While it has higher switching

Jan 19, 2017 · Layer 2 VPN is a type of VPN mode that is built and delivered on OSI layer 2 networking technologies. The entire communication from the core VPN infrastructure is forwarded in a layer 2 format on a layer 3/IP network and is converted back to layer 2 mode at the receiving end.

Cisco cBR Converged Broadband Routers Layer 2 and Layer 3 VPN Configuration Guide . Chapter Title. Flow-Based per Port-Channel Load Balancing . PDF - Complete Book (2.65 MB) PDF - This Chapter (1.09 MB) View with Adobe Reader on a variety of devices If you're providing an end-to-end LAN-to-LAN solution, use a Layer 3 service (an MPLS- or IPSec-based VPN). If you decide not to offer a Layer 3 service, but provide a site-to-site Layer 2 transport infrastructure (virtual circuits or bridged LAN-to-LAN traffic), that's fine -- as long as you're not trying to persuade customers that they can plug your LAN cable straight into their Layer 2 switches on every site and have a reliably running network. Layer 2 and Layer 3 site-to-site VPN configurations require virtualization of a full or partial production network in the Datto cloud. Supported Recovery Scenarios Test Scenarios: Due to the risk of disruption to your production network, Datto can only support Layer 2 and Layer 3 site-to-site VPN testing under specific conditions. L2 VPN and L3 VPN The Service Provider establishes Layer 2 VCs between customer sites The customer is responsible for higher layers A layer 2 switch can assign VLANs to specific switch ports, which in turn are in different layer 3 subnets, and therefore in different broadcast domains. VLANs allow for greater flexibility by allowing different layer 3 networks to be sharing the same layer 2 infrastructure.